Aesus Intermediate Speed Delta Shrink Sleeving Machine

from 60/min through 200/min

Aesus Delta Shrink Sleeving Machine

The Aesus Delta shrink sleeving machine has a larger cabinet than the eco-model and has higher speeds and can handle larger container sizes.
Aesus manufacture two styles of Delta ShrinkSleeving machines within the same basic frame.

The first and traditional style is the "Delta Shrink LB" where a Linear Blade cuts the sleeve after the sleeve has been placed over the container or onto the container neck (for neck bands).
The second style is the "Delta Shrink MB" where Multiple Blades spin around the mandrel to-part the sleeve before application to the neck or container, and then the sleeve is fired onto the container or neck as the product is presented below.

Both styles use servo feed mechanisms and servo knives to cut the sleeve.

The Delta Shrink LB is less expensive and as the sleeve is applied before cutting tighter sleeves can be used and the application is more precise, however speeds are limited to 120 per minute.
The Delta Shrink MB has to use slightly looser sleeves/neck bands, but is much faster with speeds up to 200 minute or more.

Delta Shrink Linear Blade

Mandrel application Bands or Sleeves are applied to the container, directly from the mandrel. This means there is no secondary side transfer or vacuum cups or other movement. Sleeves go right on the container.

Close sizing of Mandrel, band and container As we apply directly from the Mandrel we can have a band that more closely fits the container, thereby saving band material cost, and giving better final shrink characteristics. The closer the band fits the container the smaller percentage of shrink needed. No suction cups.

Direct application again means that neither suction cups nor vacuum is needed to hold the band. Neither humidity, dust, nor worn suction cups have any effect on the machine.

Static Electricity As the bands are not released until they are on the container static electricity has virtually no effect. If you have very short bands and lots of static then our proprietary band tacker can be enabled right at the application station to ensure the band stays put.

Large Bands The larger the container diameter the better our machines stand up against the competition because we control the band right onto the neck, and then if needed tacked. Short Bands Very short bands (3mm or so) can be applied by our ShrinkBanders, where other machines lose total control.

Band Tacker Our own optional proprietary single or dual band tackers can enabled to tack the band to the container. This is activated directly from the control panel, and saved away as a recipe to be recalled for subsequent use once setup correctly.

Dial in any length at the control panel using our unique is servo band feed mechanism. Recall recipes for subsequent set ups. Print registration Both clear and printed band material can be run on the same machine with the optional photo registration device.

Changeover: new products can be set up quickly and easily. The time saved adds up rapidly... helping pay for the machine over and over.

 Delta Shrink Multi Blade

The Delta shrink multi-blade has a servo multiple blade system that parts off the sleeve on its mandrel before applying it to the neck or container. When the container is underneath the mandrel the servocontrolled feed system spins the sleeve onto the container.

The above machine is a twin unit in a single frame allowing double the speeds of a single head, or for certain customers the second head is considered a redundant head so that while one head is having its sleeve changed the second head can be running production.



Cutting Assembly can be slid out of the machine for blade replacement, service, or adjustment. Some customers have a standby unit ready to slide in, in the unlikely event of trouble.

Noteworthy

We use Servo and not Stepper drives to feed the band, and to power the cutting blades.

User Freindly controls

 
Simple ergonomic operator panel shows machine status, controls all options, has memories to recall previous set-ups, and is password protected if requested.

Optional Accessories

Photo Registration for Printed Band Material, stops the feed at the length determined by photo registration marks on the Material.

Automatic Motorized Band Unwind, operates using a low level sensor which detects when the band unwind should feed band to alleviate web tension.

Vertical Perforation Assembly, always combined with the motorized band unwind, a hardened perforation wheel perforates the sleeve. Note with our system no additional tension is given to the web by the perforation wheel because of the motorized unwind. The Perforation placement on the band can be adjusted anywhere horizontally along the material’s layflat.

Horizontal Perforation Assembly Allowing the cap to be removed from the container while leaving the sleeve on the the container.

 

 

 

 

 

Speeds and Sleeves

Click Here for more information on Sleeve Materials and speeds.




  • Video Shrink Labeling

    Click Image below for Video - Multiple views of Aesus Shrink Labelers and Neck Banders

  • Beer Can Shrink Labeling

    Click Image below for Video - Empty Beer Can Labeling and Shrinking